B&K Vibro Acceleration Sensors in Nigeria: How to Choose the Right Sensor for Pumps, Motors and Fans

A vibration sensor can fit the mounting point and still be the wrong sensor for the job.

The connector may look familiar. The housing may be almost identical. But differences in sensitivity, frequency response, power requirements or installation can affect whether the sensor produces useful measurements with your monitoring system.

For engineers and procurement teams sourcing B&K Vibro acceleration sensors in Nigeria, the goal is not simply to buy an accelerometer. It is to specify a sensor that suits the machine, the measurement task and the connected equipment.

This guide focuses on product selection and replacement procurement for pumps, motors, fans and other rotating machinery. It is not another guide to diagnosing vibration faults.

Already have a sensor code? Request a B&K Vibro quotation with the complete model number, quantity and application details.

What is an acceleration sensor?

An acceleration sensor, also called an accelerometer, measures acceleration at its mounting location. Industrial vibration accelerometers can be used to collect vibration measurements from machine housings and bearing housings.

The usefulness of those measurements depends on more than the sensor alone. The mounting arrangement, cable, measurement channel and monitoring configuration all matter.

B&K Vibro’s sensor documentation includes acceleration-sensor designs with constant-current power requirements. Those requirements must be matched to the receiving equipment rather than assumed from the connector.

Acceleration sensors are not interchangeable with every vibration sensor

“Vibration sensor” is a broad purchasing description. Before comparing products, establish whether the application calls for an acceleration sensor, a velocity sensor or another measurement arrangement.

GIL Automation’s catalog includes AS-series acceleration-sensor entries and VS-series velocity-sensor entries. These should not be treated as interchangeable simply because both are used for vibration measurement.

For a replacement, identify what the existing system expects. For a new installation, define the measurement objective before selecting the sensor.

Seven checks before choosing a B&K Vibro acceleration sensor

1. Define the machine and measurement objective

Start with the asset: is it a motor, pump, fan, gearbox, compressor or another machine? Record its operating-speed range, the proposed measurement location and the purpose of the measurement.

A sensor selected for a general machine-vibration measurement should not automatically be assumed suitable for every specialised measurement task. Describe what the engineering team needs the measurement to reveal, rather than requesting only a familiar model.

2. Check sensitivity and measurement-channel configuration

Sensitivity describes the relationship between the sensor’s electrical output and the acceleration it measures. It is commonly expressed in units such as mV/g.

For example, B&K Vibro’s published AS-062 and AS-063 instructions specify a nominal sensitivity of 100 mV/g under stated reference conditions. That does not make the models identical in every other respect.

Check the exact sensor documentation and ensure the receiving channel is configured for the installed sensor’s sensitivity. A replacement assessment should include the monitoring configuration, not just the item being removed.

3. Match the useful frequency range to the application

Do not select an accelerometer from sensitivity alone. Review its documented frequency response against the measurement requirements.

Machine operating conditions and the monitoring method help determine which frequencies matter. The engineering assessment should consider the usable measurement range of the complete arrangement, including the mounting and receiving equipment.

Ask for the relevant datasheet rather than accepting “suitable for all rotating equipment” as a specification.

4. Confirm electrical and monitoring-system compatibility

Identify the connected monitoring unit, data-acquisition device or analyser. Confirm the required sensor supply, input arrangement and signal characteristics against its documentation.

For constant-current sensors, verify that the connected equipment provides the appropriate excitation. A matching plug is not evidence of electrical compatibility.

Include the monitoring-equipment model in your enquiry, particularly when replacing an older sensor or considering an alternative.

5. Review temperature and environmental requirements

Record the conditions at the actual sensor location, not just the general plant environment. Include expected temperature, exposure to moisture or contaminants, and relevant cable-routing conditions.

If the location is hazardous, provide the applicable area requirements and request verification of the exact sensor variant and installation documentation. Do not infer hazardous-area suitability from the brand name or product family.

6. Specify the mounting arrangement

Mounting is part of the measurement system, not an afterthought. B&K Vibro’s sensor instructions emphasise appropriate rigid mounting for the relevant designs.

Before ordering, confirm the mounting interface, available space, cable exit direction and any required mounting accessories. Use the selected model’s instructions for installation details.

Do not transfer a mounting torque or installation method from a different sensor model without checking its documentation.

7. Check cables, connectors and the complete model code

Identify whether the application uses an integral cable or a separate connector arrangement. Confirm the necessary cable length, connector compatibility and any accessories included in the quotation.

Record the full model designation, including suffixes. GIL’s catalog contains entries such as AS-062, AS-062/T1, AS-063, AS-069 and AS-667. These are useful starting points for enquiries, not a statement that they are equivalent or immediately available.

Request confirmation of the exact configuration, supporting documentation and availability before raising a purchase order.

Replacing a sensor? Do not rely on appearance alone

A sensor replacement enquiry is stronger when it includes evidence from the installed system.

Photograph the label, connector and mounting location. Record the existing sensor code and monitoring-equipment model. If the replacement is being considered because of unusual readings, describe the symptoms and any recent changes to the machine, cable or configuration.

An unusual reading does not by itself prove that the sensor has failed. Appropriate checks should be performed by competent personnel under the site’s procedures before deciding what needs replacement.

What to include in a B&K Vibro sensor enquiry

  • Complete sensor model and part number, where available.
  • Required quantity.
  • New installation or replacement requirement.
  • Machine type and operating-speed range.
  • Measurement objective and proposed mounting location.
  • Monitoring unit or analyser manufacturer and model.
  • Required sensitivity and electrical interface, if known.
  • Temperature and environmental conditions.
  • Applicable hazardous-area requirements, where relevant.
  • Mounting details, connector type and cable length.
  • Photographs and available equipment drawings.
  • Delivery location and required project date.

If you do not have every detail, send what is available and identify the missing information. A clear starting point is better than an assumed specification.

Sensor supply, vibration analysis and condition monitoring are different requirements

A request for a sensor is a product-selection enquiry. An investigation into abnormal machine vibration is a separate technical service requirement.

Vibration analysis examines vibration measurements in the context of the machine and its operating conditions. Condition monitoring is broader and may combine multiple equipment-health indicators over time.

When contacting GIL Automation, state whether you need a replacement sensor, help specifying a measurement arrangement, or a separate vibration-analysis assessment. This helps define the appropriate scope.

Frequently asked questions

Are all B&K Vibro AS-series sensors interchangeable?

No blanket interchangeability should be assumed. Compare the full model designation, sensitivity, electrical requirements, frequency response, environmental limits, mounting and cable arrangement.

Is a 100 mV/g sensitivity enough information to select a sensor?

No. Sensitivity is only one selection parameter. The complete sensor specification and monitoring-system compatibility must also be checked.

Can I replace a velocity sensor with an acceleration sensor?

Do not treat this as a direct substitution. The measurement requirement and receiving equipment must be reviewed before selecting a different sensor type.

Can GIL quote from an existing sensor code?

Send the complete code, quantity and available photographs through the quotation form. Include the application and monitoring-equipment details so the requirement can be reviewed. Request confirmation of specifications and availability.

Does a new sensor diagnose a machine fault automatically?

No. A sensor provides measurements. Useful interpretation also depends on the acquisition equipment, configuration, operating context and appropriate analysis.

Request a B&K Vibro sensor quotation in Nigeria

Preparing a project specification or replacing an installed sensor? Send GIL Automation your exact B&K Vibro model code, quantity, machine details and monitoring-system information.

In the form below, mention “B&K Vibro acceleration sensor” and include any required cables or mounting accessories. Ask for confirmation of the proposed configuration, documentation and availability.

If the form does not display, open the quotation form directly or use our Request a Quote page.

This guide supports product selection and procurement. It does not replace the exact sensor’s installation instructions or a competent engineering assessment. Product listings do not confirm stock, lead time or application suitability.

Manufacturer references

Acceleration sensors, B&k vibro, Instrumentation, Nigeria, Rotating equipment, Vibration sensors